基于图像识别的机械振动信号特征提取与寿命预测方法研究

滚动轴承作为许多机械设备的关键组件,被广泛应用于机械制造、航空航天等领域,其健康状态直接影响了相应设备的剩余寿命,因此在设备故障预测与健康管理(Prognostics and Health Management, PHM)领域,滚动轴承寿命预测具有很高的研究价值。目前基于数据驱动的轴承寿命预测方法主要利用特征提取并构造健康因子(Health Indicator, HI),然而在这一过程中特征的选择与融合依然依赖于专家先验知识,并且健康因子也很难从复杂的时序数据中进行提取。因此,提出了一种新型的数据驱动寿命预测算法,在特征提取方面,通过连续小波变换(Continuous Wavelet Transform,CWT)将传感器振动信号转换为时频谱图,再通过深度残差网络(Deep residual network, ResNet)结合时空卷积网络(Temporal Convolutional Network, TCN)将时频谱图中的时域频域特征构造成为健康因子,最后完成剩余寿命预测。本研究在PRONOSTIA数据集上与现有的数据驱动算法进行了对比,证明了该算法可以更准确地完成剩余寿命预测。     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

Assessment of between-floor structural and topological properties on cognitive map development in multilevel built environments

The present study investigated cognitive map development in multilevel built environments. Three experiments were conducted in complex virtual buildings to examine the effects of five between-floor structural factors that may impede the accuracy of humans’ ability to build multilevel cognitive maps. Results from Experiments 1 and 2 (of three experiments) revealed that difficulties in developing multilevel cognitive maps are not solely caused by the z-axis offset, as is suggested in the literature, but are due to the factorial combination of a between-floor overlap and a z-axis offset. Results from Experiment 2 showed that this process becomes substantially more difficult when the reference directions between different floors have an angular offset from each other. Finally, results from Experiment 3 demonstrated that confusing between-floor heading shifts in aligned buildings did not make it reliably harder to build multilevel cognitive maps. The implications of these findings are discussed in terms of theories of mental representations in multilayered three-dimensional spaces, as well as for architectural design.     

Simulating planetary wave propagation to the upper atmosphere during stratospheric warming events at different mountain wave scenarios

Parameterization schemes of atmospheric normal modes (NMs) and orographic gravity waves (OGWs) have been implemented into the mechanistic Middle and Upper Atmosphere Model (MUAM) simulating atmospheric general circulation. Based on the 12-members ensemble of runs with the MUAM, a composite of the stratospheric warming (SW) has been constructed using the UK Met Office data as the lower boundary conditions. The simulation results show that OGW amplitudes increase at altitudes above 30 km in the Northern Hemisphere after the SW event. At altitudes of about 50 km, OGWs have largest amplitudes over North American and European mountain systems before and during the composite SW, and over Himalayas after the SW. Simulations demonstrate substantial (up to 50–70%) variations of amplitudes of stationary planetary waves (PWs) during and after the SW in the mesosphere-lower thermosphere of the Northern Hemisphere. Westward travelling NMs have amplitude maxima not only in the Northern, but also in the Southern Hemisphere, where these modes have waveguides in the middle and upper atmosphere. Simulated variations of PW and NM amplitudes correspond to changes in the mean zonal wind, EP-fluxes and wave refractive index at different phases of the composite SW events. Inclusion of the parameterization of OGW effects leads to decreases in amplitudes (up to 15%) of almost all SPWs before and after the SW event and their increase (up to 40–60%) after the SW in the stratosphere and mesosphere at middle and high northern latitudes. It is suggested that observed changes in NM amplitudes in the Southern Hemisphere during SW could be caused by divergence of increased southward EP-flux. This EP-flux increases due to OGW drag before SW and extends into the Southern Hemisphere.     

面向快速响应产品的星上目标定位及识别方法

针对遥感卫星星上目标的定位及识别，本文面向快速响应应用需求，首先对星上目标定位及识别工作模式进行研究，总结出狭义和广义两种模式，其次重点对像方-物方坐标双向定位算法进行梳理，并针对典型地物目标星上自动识别算法提出研究思路，最后给出算法的应用方法流程。本文研究为快速响应产品星上智能处理提供方法参考。     

SSPS-OMEGA超大型球形聚光器结构拓扑构型与设计

为同时兼顾千米量级尺度空间太阳能电站聚光系统的在轨发射安装难度、光学收集效率、稳定性及结构工艺等多方面的因素，提出采用基于球面正多面体的经纬线划分法模块化构建球形聚光器。该方法不仅可实现基础划分单元分布均匀、规格种类少，降低在轨构建与运载发射难度。而且只要合理控制弧高等分数和基础划分单元的口径就可以同时保证聚光系统的光学收集效率。理论与仿真结果显示，当弧高等分数为24时，该划分法共有25种基础单元件，整个球面被分成5762块。并且此时模块化构建的实际球形聚光器的光学收集效率与理想球面相比基本保持不变，解决了太阳能电站聚光系统设计中存在的关键问题。     

基于深度学习的毫米波和亚毫米波成像仪的图像增强技术

风云四号卫星毫米波和亚毫米波成像仪(MMSI)数据根据采样方式分为过采样和非过采样数据。由于采样方式的影响,非过采样数据在采样过程中会有一定的信息损失。为解决采用简单的线性插值方法做精细化处理时提升精度有限问题,采用基于深度学习的方法增强MMSI亮温图像,设计卷积神经网络重建风云四号卫星MMSI的亮温图像和风云三号卫星微波成像仪亮温图像。实验结果显示:相比传统的双三次插值方法,在风云三号卫星微波成像仪亮温图像样本上峰值信噪比提升了1.13dB,结构相似度提升了0.01。实验结果表明:对于非过采样亮温数据,采用基于深度学习的方法增强图像具有更高的精度,同时可在其他微波探测仪数据中使用,具有很强的普适性。     

Non-stationarity and cross-correlation effects in the MHD solar activity

The analysis of turbulent processes in sunspots and pores which are self-organizing long-lived magnetic structures is a complicated and not yet solved problem. The present work focuses on studying such magneto-hydrodynamic (MHD) formations on the basis of flicker-noise spectroscopy using a new method of multi-parametric analysis. The non-stationarity and cross-correlation effects taking place in solar activity dynamics are considered. The calculated maximum values of non-stationarity factor may become precursors of significant restructuring in solar magnetic activity. The introduced cross-correlation functions enable us to judge synchronization effects between the signals of various solar activity indicators registered simultaneously.     

考虑探测构形的多飞行器协同探测与制导一体化设计

针对多飞行器协同拦截机动目标时几何构形会影响协同探测和制导效果的问题，基于最优控制理论提出一种考虑探测构形的协同探测与制导一体化设计方法。基于飞行器相对运动学、动力学方程和双视线协同探测原理，建立了协同拦截模型。在制导设计中引入视线分离角参量以调制协同探测几何构形、减小相对距离探测误差，从而在制导全程增强协同探测效果。将相对距离协同探测结果应用到剩余时间和制导律解算中，基于最优控制理论实现协同探测与制导环节一体化设计。仿真结果表明：在目标进行不同程度机动的情况下，与修正比例导引律相比，所提方法在协同探测和制导方面均具有明显优势。     

基于射线追踪的快速雷达图像仿真方法

为了解决目标识别、隐身目标设计等研究领域对雷达图像需求日益增加的问题,提出了一种基于射线追踪的快速雷达图像仿真方法。该方法利用射线追踪计算每一个射线管的散射电场及其在雷达成像平面的投影坐标,通过将所有射线管的贡献在像域进行累加得到1幅二维雷达图像。通过对不同路径射线的聚类,可实现对散射贡献的分离,从而建立目标部件与强散射源的对应关系,并对复杂目标雷达图像进行解释。给出了Slicy目标的快速雷达图像仿真与算例分析,分析结果表明:基于射线追踪的快速雷达图像仿真方法可对复杂雷达图像进行有效预测,并能对强散射源进行成因分析。